Apr 14, 2025 Leave a message

Troubleshooting of Spiral Conveyor

1. The connecting bolt of the head section is twisted and broken

Reason: The connecting bolt at the head section bears the torque of the fully loaded motor, while the torque borne by the spiral section and connecting bolt at the back decreases.

Solution: Use stronger bolts at the head section or connect with three bolts to prevent the connecting bolts from being cut off.

 

2. Suspension bearing issues

Reason: When the suspension bearing is working, it is buried in the material. If the sealing and lubrication are not good, it is easy for material particles to enter the contact surface between the bearing and the journal, accelerating wear.

resolvent:

Select high-quality bearing shells and ensure good sealing and lubrication.

Ensure that the suspension bearings are installed concentric with the connecting shaft, and that each suspension bearing is concentric to ensure the linearity of each section of the spiral.

There should be a gap (usually 10-20mm) between the end face and the spiral shaft end face.

 

3. The conveyor belt slips

Reason: Insufficient friction between the conveyor belt and the driving drum may be caused by high material humidity, surface wear of the drum, or insufficient tension of the conveyor belt.

Solution: Adjust the tension of the conveyor belt, clean the surface of the drum, and increase friction; Reduce material humidity; Check if the transmission device is functioning properly.

 

4. The conveyor belt deviates from the track

Reason: The conveyor belt deviated from the predetermined track during operation, which may be caused by improper installation, uneven tension of the conveyor belt, or uneven distribution of materials.

Solution: Adjust the tension of the conveyor belt to ensure balanced tension on both sides; Check the installation position of the conveyor belt and rollers to ensure they are on the correct track; Clean the materials to ensure they are evenly distributed on the conveyor belt.

 

5. Motor overload

Reason: Excessive material flow leads to excessive motor load.

Solution: Reduce material flow and alleviate motor load; Check and solve the problem of conveyor belt slippage; Check if the motor is functioning properly, and repair or replace it promptly if there are any issues.

 

6. Bearing damage

Reason: The bearing is damaged due to excessive load or foreign object intrusion during operation.

Solution: Check the lubrication condition of the bearings to ensure their normal operation; Regularly replace bearings to avoid excessive wear and tear; Strengthen equipment maintenance and upkeep to prevent foreign objects from entering.

 

7. Gearbox malfunction

Reason: Wear of internal components of the gearbox or lubrication system issues.

Solution: Check the lubrication system of the gearbox to ensure its normal operation; Regularly replace the internal parts of the gearbox to maintain its good working condition; Strengthen the daily maintenance and upkeep of equipment.

 

8. Blockage

Reason: Material entanglement or blockage of intermediate suspension bearings.

 

Resolvent:

Reasonably select the technical parameters of the screw conveyor, such as the speed of the slow speed screw conveyor should not be too high.

Strictly follow the operating procedures to achieve no-load starting and no-load stopping; Ensure continuous and uniform feeding.

Increase the discharge port or extend the end of the material trough to address the issue of poor or untimely discharge.

Necessary cleaning should be carried out on the materials entering the conveyor to prevent large or fibrous impurities from entering the machine and causing blockages.

 

Try to minimize the lateral size of the middle suspension bearing to reduce the possibility of material blockage when passing through the middle bearing.

Install silo level sensors and blockage sensors to achieve automatic control and alarm.

Install an anti blocking valve on the discharge end cover plate. When a blockage occurs, due to material accumulation, the anti blocking door is pushed open and the power is cut off through the travel switch.

 

Daily maintenance and upkeep

In order to extend the service life of the screw conveyor and reduce the occurrence of faults, daily maintenance and upkeep are equally important. Including but not limited to:

Check the operation status of the screw conveyor every day, including key components such as motors, reducers, bearings, etc., to ensure that there are no abnormal sounds or vibrations.

Regularly clean the residue inside the screw conveyor, keep the equipment clean, and prevent blockage and wear.

Check and tighten all bolts to ensure the stability of the equipment structure and prevent equipment failure caused by loose bolts.

Regularly lubricate bearings, chains, and other parts according to equipment requirements to maintain good lubrication and reduce wear.

The above is an overview of common faults and their troubleshooting methods for screw conveyors. For specific issues, it is recommended to take corresponding measures based on the actual situation and seek professional assistance when necessary.

Send Inquiry

Home

Phone

E-mail

Inquiry